The Secret ThinkPad Powerbutton Code to Bring Dead Laptops Back to Life (2007) (masnick.com)

286 points by sammatilda 12 hours ago

legacynl 11 hours ago

From a former call-center phone operator, I think the 10 1-sec pushes, is just a way to make sure the customer presses the buttons long enough. In our callcenter we often had to ask customer to hold the reset button on their router for 3 seconds. When the router didn't reboot, I would send replacements, until a colleague advised me to tell customers to hold the button for 10 seconds. Apparently when you ask customers to hold the button for 3 seconds, some will actually only hold it for 1 or 2 seconds. Suddenly most customers were able to reset their routers.

rozularen 10 hours ago

This just saved my Lenovo Legion laptop! :) My gf dropped it a few days ago, and it hadn't booted since. I had already tried the static discharge procedure, but it didn't work for some reason. After reading your comment, I figured I'd give it one more shot, and it finally booted up. Thanks a lot!

devsda 7 hours ago

My non lenovo laptop requires holding power button for 10 seconds or more to even charge after an accidental deep discharge(modern standby sucks!). I got a few scares when it didn't power up even after 10 seconds. It did comeback up when checking it later.

I guess there are hardware level variances for the time needed or its just variance in perception of time across individuals, specially when panicking about our precious devices.

dylan604 6 hours ago

rozularen 7 hours ago

burnte 4 hours ago

You are correct. When I am talking to people I usually tell them to hold it for 20 seconds and then state it's longer than it feels, so keep holding, and that USUALLY gets them past the ten second mark. Or I'll say hold it down and I'll tell you when to let it go. The power button itself isn't even REQUIRED but speeds up capacitor discharge. Once you disconnect the battery you just need all flea power to stop because Lenovo keeps some circuitry alive 24/7. Holding the power button helps complete the circuit and drain flea power fast.

EduardoBautista 3 hours ago

When I worked at a call center, we would ask them to switch the ends of the Ethernet cables just to make sure they were fully unplugged and plugged back in.

gpvos 9 hours ago

The article says 10 pushes at 1-second intervals, which can each still be a very short push. Otherwise, yes, better press a little too long.

orev 5 hours ago

Just like you never ask them if something is plugged in, because the response you’ll get is “of course it’s plugged in, I’m not an idiot!” But they won’t actually check if it’s plugged in.

Instead, you ask them to check the wires because “sometimes they get loose”. In that context, they’ll check, and might see they forgot to plug it in. They’ll plug it in, but will only say “it’s working now” without telling you that they forgot. It’s fine because now the problem is actually solved.

esalman 6 hours ago

Somewhat related - I asked Opus to add a 120 second timeout to LLM gateways. When I went back to inspect the code, I noticed it added a 10 seconds buffer, or n+10 seconds total timeout.

dnmc 7 hours ago

I wonder if these customers started counting seconds at one instead of zero.

throwaway_new_1 7 hours ago

Or they counted seconds like they would just count from one to three. One count is much less than a second when you are just counting.

baby_souffle 3 hours ago

We did similar.

"I need the serial number for your power supply. It's printed on the plug between the two prongs. Remove the socket from the wall and read me the number printed between the two prongs"

We only used that when we knew you were lying about having already restarted it.

brudgers an hour ago

“Unplug the power cord from the wall and blow on the prongs three times.”

Freestyler_3 11 hours ago

Its a standard step in troubleshooting "bricked" devices, not specifically the amount of pushes but the unplug any power source and then hit the power on button to discharge power left in the system (caps)

pockybum522 11 hours ago

Correct on all counts. Static discharge is a strange way for the article (and tech on the phone) to say discharging capacitors but that's what it's doing.

kotaKat 11 hours ago

The problem is if you sound too smart to the customer, it's an insult to their intelligence.

Telling them "we're draining the flea power" and now the customer's freaking out they have a bug infestation and Dell has unleashed a storm of locusts upon them.

freeopinion 9 hours ago

Freestyler_3 7 hours ago

0xbadcafebee 9 hours ago

AdmiralAsshat 10 hours ago

Yeah, the advice sounded similar to what I recall a Toshiba tech once telling my dad to do when his Toshiba laptop wouldn't power on.

praash 8 hours ago

People should be warned that high power circuits can retain a deadly charge when unplugged. Until my 20s I always smirked at the lightning bolt stickers thinking how unplugging obviously makes them safe.

dimavolo 6 hours ago

I have a little Anker GaN usb charger cube, into which I often plug one of those flexible IKEA LED USB-C reading lights.

Every time I unplug the charger from the wall, I’m still surprised when the LED reading light stays on for an extra second or two, “unplugged”

philistine 5 hours ago

theandrewbailey 10 hours ago

> Two months ago, I got a new laptop. It’s a Lenovo Thinkpad z61t. I actually ordered a t61, but I accidentally got the z61 instead — and, I actually really like it.

The college I went to supplied every student with a Thinkpad. Everyone in my quarter got the z61p. (This college went year-round, a new class started every 3 months.) No other students before or after had z61p Thinkpads.

Despite the high quality everyone regarded Thinkpads with, this model had some issues that only exposed themselves in a large deployment. (I don't recall any that affected my Thinkpad.) At one point, they had a Lenovo service guy come out and replace the power board in every z61p on campus.

When students graduate, they could buy their Thinkpad for $1. I asked if they accepted change. It's probably the best laptop that I will ever buy with change. It kept working for another 5 years. Now I'm kicking myself that I had not stumbled across this back then before I threw it out.

Today, I work in an ewaste recycling company. I haven't come across any z61p Thinkpads yet. (but I'll remember this 'one neat trick')

fullstop 9 hours ago

> Today, I work in an ewaste recycling company. I haven't come across any z61p Thinkpads yet.

My daughter started a laptop recycling club at her university where they refurbish old laptops, mostly those without the ability to run newer versions of Windows, and install Linux on them. The laptops are then paired with students who are unable to afford a laptop, through the disabilities office. The devices which are broken beyond repair go to an ewaste facility like the one you work at.

Thanks for doing what you do -- there's so much electronic waste out there!

fnimick 9 hours ago

That's so lovely to hear. I do the same thing on a small scale locally as a solo passion project - I have gotten 30+ laptops to students in need that would otherwise have gone to e-waste.

Out of curiosity, what distribution do they use? I've got quite a few laptops sitting around atm as I'm waiting for a user-friendly atomic distribution to become available.

fullstop 9 hours ago

theandrewbailey 9 hours ago

> mostly those without the ability to run newer versions of Windows, and install Linux on them.

We don't have a Windows OEM license, so between the certifications and auditors, the things we sell have nothing, or Linux. The things I list on the company Ebay account have Mint (due to their OEM install option) or Debian (touchscreens work best with KDE, IMO).

https://www.ebay.com/str/evolutionecycling

fullstop 9 hours ago

asveikau 7 hours ago

A few years before that model came out, I had a thinkpad R40. It seems very similar. In fact when I Google z61p, many people compare it to R60.

I had to abandon it circa 2007 because the GPU became de-soldered. I was able to fix it for a few months by hitting it with a heat gun, but it eventually became bad again. I was sad to lose it.

ToucanLoucan 9 hours ago

We use thinkpads at our office and I mostly like them, though they can't seem to track their powered state worth a damn (which weirdly kind of intersects with the topic of the thread):

I'm primarily a mac user due to my work but I have a thinkpad in addition to my Macbook because the company is still largely a windows shop, and accessing a lot of source code, plus managing my AD account and whatnot all needs doing with the thinkpad, and honestly that doesn't bother me, apart from seemingly every time I pull it out of my bag and it's been awhile, I have to push the power button... then hold the power button... then hold the power button... then push it a couple times... and go around with this routine for awhile before the stupid screen finally lights and it boots up.

And I have no reason to believe this is a fault, it's done this since it was issued to me and I've witnessed coworkers also struggling with it. But yeah. Overall, great machine, I enjoy the little nipple-mouse, good stuff, but the thing seems to struggle hard with just turning off and on.

matltc 7 hours ago

I get ACPI errors on every boot where I have the adapter plugged in with priority <= 3 in systemd, something about the power tables being all fubar. Hasn't really had a noticeable effect except once in a while it will beep super loud and put a warning before it starts bootstrapping about using non-standard charger despite me using the one it came with. Maybe happens when battery is low, I plug it in, bad power state is in flash memory or can't be read, throttles charging, fw never gets the message so it warns? I never had to do an EC reset to fix that though, just a reboot unplugged. Also different model (IdeaPad) but probably sameish firmware and stuff

thesuitonym 6 hours ago

> this model had some issues that only exposed themselves in a large deployment.

Ah, so Lenovo did keep something from the IBM days. =)

I'm in charge of IT procurement for my company, and we've transitioned away from ThinkPads. I like them, but there's just no quality control at Lenovo. At one point, we ordered about 20 laptops and 4 or 5 came with the webcams upside down. Damaged monitors, incorrectly seated RAM, and all kinds of other issues plague us. Recently they sent out a firmware patch or something that's causing the chargers to zap the thunderbolt ports. Seriously! People are reporting that they unplug their laptop and see smoke come out of the charging port!

And as if that weren't bad enough, they've recently changed out their local onsite tech company, so "Next business day" support ends up being 3-5 business day support...If we're lucky.

hobo123 5 hours ago

I like my T490 but it's also a far shot from earlier models. Sometimes it would short-circuit when carrying it around and hang until I killed it. I had to apply isolation tape between part of the main board and the casing bottom so they don't touch, which caused the issue.

Is really sad to see they turned into Just Another Vendor (or rather were bought by one).

Any recommendations on what to buy as a future laptop?

YeGoblynQueenne 8 hours ago

I was in Singapore recently (far away from home) with my T15p and someone started drilling with an electric drill in another room in the hotel I was staying and my laptop died. No power-on, no power button led, no power jack led turning on. I took a paperclip from the reception and reset the laptop by removing the battery, then inserting the paperclip end in the reset hole at the bottom and counting to 30, just to be sure.

Then about a couple weeks after I returned from Singapore, my T15p died once more. Again, no power-on, no power button led, no power jack led. I tried the reset cycle again, battery out, paper clip in (actually used my phone's tool this time).

Guess what. This time the magick trick didn't work and my laptop stayed dead. For good. Turns out the fan had clogged up with so much cruft that the system overheated and the entire board had to be changed. Fortunately covered by premium insurance with home service.

Morale of the story: the magick trick is not magick and it doesn't always work. Sometimes your laptop is really dead and you can't revive it by pushing buttons.

Just saying because I get this vibe that this is a super secret trick from the ninth dimension and it will fix all wrongs ever. It won't right?

Sesse__ 11 hours ago

My ThinkPad (X280) has a much simpler way of dealing with this: There's a tiny hole in the bottom, and if you stick something sharp into it and hold for a while, the embedded controller will reboot (or was it turn off?).

It basically saved me from buying a new laptop at some point, when it completely refused to charge the battery for whatever weird reason (it would charge for a second or so, and then cut off, then the charger would restart it, new cut, etc.).

omnimus 9 hours ago

I think that may be solving different issue. I needed to do this for lenovo yoga after using random USB-C charger that the laptop couldn't negotiate power delivery with. The controller got confused and that pin can reset the controller. It doesn't discharge the battery.

doublepg23 2 hours ago

Just had to do this with my X1 Titanium after it refused to reboot during a BIOS upgrade.

dlgeek 9 hours ago

It's a battery disconnect. So it completely cuts off power for the embedded controller. (You hold for the caps to discharge).

ho_schi 8 hours ago

As far as I know:

The tiny hole resets the Embedded-Controller (EC). I think on older ThinkPads the same is done by pressing for 10 seconds continuously the power button, while the battery is removed. Other sources say 30 seconds pressing, but for me 10 were enough.

We cannot remove the battery on newer models, therefore the tiny hole.

rzzzt 2 hours ago

Newer ones have a menu item in the BIOS for disconnecting the non-removable battery (it will be connected and charged again once it's back on the charger).

YeGoblynQueenne 7 hours ago

We can on my T15p gen 3, bought 2021, and it also has a tiny hole. AFAICT it does the same thing as pressing the power button in that it discharges ... electrical stuff? It's all electric in there.

forsalebypwner 3 hours ago

andrewshadura 10 hours ago

Didn't help with X270. The only thing that helped was buying the original rectangular plug charger and using that instead of USB-C.

Sesse__ 9 hours ago

X280 and newer doesn't have a rectangular plug anymore…

andrewshadura 8 hours ago

dizhn 10 hours ago

I needed this exactly once on my T480S and it was great to have it.

ImPleadThe5th 11 hours ago

I have a dead Lenovo gaming laptop that has been sitting around for the last year. Literally just tried this. And it posted for the first time since it bricked and booted right into my drive once I plugged it back in.

I knew about discharging capacitors and tried holding the power button down and pulsing it before. But I guess this time its magic?

I bet it'll stop working again shortly, but was funny to see.

tacker2000 9 hours ago

Strange... wouldnt these capacitors be discharged anyway if it's been sitting around for so long?

ImPleadThe5th 4 hours ago

Likely the case. I did not control for that haha, this post just reminded me it was in my closet.

dtgriscom 10 hours ago

Tech support for naive (no offense) customers is an art. A friend's mom was a customer service rep for RCA TVs back in the day (way, way back in the day). Customers would call and complain that their TVs were doing nothing: no lights, nothing.

The standard response would be to ask them to pull the TV's (non-polarized) plug, reverse it, and plug it back in. This was generally successful, NOT because the plug polarity mattered, but because the customer had actually forgotten to plug in their TV.

If the rep had said "is your TV plugged in?", many customers would indignantly say "Of course!" without even checking. The "reverse your plug" request was more successful because it sounded like the customer was doing something intelligent. And, when they went to perform this task, they would discoverer that they'd forgotten to plug their TVs in. The customer could then report that the reversal worked, nobody would mention the unplugged TV, and everyone would be happy.

jeroenhd 8 hours ago

Similarly: when I needed to guide users to check the wiring of their DSL modems, they of course always claimed that everything was hooked up exactly as stated on the little diagram that we sent out.

Asking them to blow the dust out of the RJ11 ports made them remove the cables and actually plug them in the right way around. Hard to say how many of them just got it right the second time and how many of them noticed their mistake but didn't want to admit it, but either way, it saved them waiting a day for a tech to come out (often at their own cost).

standeven 7 hours ago

As a bonus, half the time the customer unplugs their own phone line, dropping your average call time metric.

YeGoblynQueenne 7 hours ago

Yes, well, one time I was setting up on a new PC and I was getting a weird linux error about the network being unreachable when I tried to install some stuff. I went to the support desk and told one of the IT gods there what happened (those guys were really gods). He mumbled something like "I think I know what that is" and walked back to my desk with me. He knelt behind the tower, connected the ethernet cable and said "try now".

I have never felt so embarrassed in my entire life. I don't think I ever will.

sosuke 4 hours ago

I've only believed the ethernet cable is connected if I get that satisfying "click" sound.

igleria 9 hours ago

This is so thoughtful that it should be able to be transposed to software support

nullc 6 hours ago

I worked at a PC shop as a teen. People would bring home their newly fixed system then phone it to complain that it was dead.

Inevitably this would be because the switch on the back was OFF but the user normally turns their computer on through some kind of power strip.

Any form of asking them to turn that switch ON wouldn't work-- either they'd angrily say they already turned it on, pretend to do so, or just refuse.

It was far more effective to tell them to reach behind and turn the switch OFF. "Oh! it's coming on!".

Much later I worked as a field engineer for Juniper and was impressed by the number of times the customer and I would grind on an issue only to try support and have them solve it with basic procedural steps that avoid assumptions and begin with the basics-- stuff that "obviously" doesn't apply. Ever since I've tried to remember that experience and apply it to my own troubleshooting and I think it's been helpful.

haritha-j 11 hours ago

Not limited to thinkpads by any means, this is I believe common to most laptops. On my last MSI (no removable battery), the trick was to unplug, hold down the power button for 30 seconds, maybe press the power button a couple of times. I froget what the issue it fixed was, but it wasn't totally dead. but the logic was static discharge.

varispeed 11 hours ago

That was the standard way to power up my Dell XPS as otherwise it wouldn't. Such a chore. So many stand ups missed because it would often take half an hour for it to "click" and power on.

bajard 4 hours ago

Yes, I had seen a lot of this kind of weird behavior on many laptops from different manufacturers. They refuse to start. Sometimes I'm convinced they are dead beyond repair. Then, after a few hours, they just boot like nothing happened. Sometimes it's related to the battery (but they also refuse to boot when plugged in). Sometimes it has nothing to do with the battery.

I think it's Microsoft's fault, as they forced manufacturers to remove user access to the BIOS/UEFI as much as possible.

anilakar 10 hours ago

I had a Microsoft Sidewinder 2 joystick that suffered from static buildup. Shelving it for a month always fixed the issue by itself. I wonder if there were hidden tricks like this to unbrick the controller.

xattt 10 hours ago

Is it static buildup, or is there a failing cap that gets reformed after a period without power?

jwrallie 10 hours ago

It works even for non-ThinkPads. My coworker was looking clueless at his open Asus laptop. I said the first thing I’d try is unplugging the battery and holding the power button. He still thinks I’m a wizard.

Trlog 10 hours ago

A lot of laptops reset the EC if you hold the power button long enough, so it's always worth trying. I've had to do this on my MSI gaming laptop because Linux wasn't able to set power states on the Nvidia GPU, which was magically resolved with an EC reset.

Neil44 9 hours ago

Seems the laptop failed to sleep and overheated in the bag. Maybe it hadn't cooled down enough the first time he popped the battery out. Modern laptops that don't have removable batteries often respond to a 20-30 second hold of power - e.g. Dells do that.

YeGoblynQueenne 7 hours ago

You know, that sounds more like it than the static discharge thing.

matltc 7 hours ago

I have an IdeaPad flex 5 14alc05 that has something like this. Got it from Claude, not sure if documented. It came with a pos nic (mediatek mt7xxx) that basically sucks and would drop wifi randomly and permanently until I did this. It was just hold power for 1 min, I think Claude called it an embedded controller (EC) reset. Temporarily solved the problem, but the only thing that fixed it was to swap in an Intel ax210. Snapped the conn from the old nic into the antenna while removing, bought a replacement but works fine with just the one so far

mystifyingpoi 9 hours ago

Is there a special combination for phones with glued-in battery? Recently I had an issue with some older Samsung smartphone, where the touchscreen refused to drag lines across the lock pattern. I spent solid 20 minutes trying to unlock it, then thought for another 20 minutes how to reboot it - no hole, power button does nothing, battery at 100% so discharging it would take a day of continuously turning on the screen (or maybe suck the power via USB load).

By accident, I've discovered that yanking out the SIM card shows up the notification that can be used to reboot the phone without unlocking. After reboot, everything worked fine again.

cryzinger 5 hours ago

I don't know if this works on all versions/devices, or whether it would've worked in your lock screen scenario, but pressing and holding Power + Volume Up or Power + Volume Down (I think this also varies by device) can sometimes force a reboot.

You can also try one of those button combos to start an Android phone in recovery mode, which is occasionally useful, but you have to be careful with some of the data-wiping options :P

coldpie 9 hours ago

On most Android phones for the past ~10 years, just holding the power button down for like 10 or maybe 30 seconds does a hardware reboot. I know this because it happens in my pocket all the freaking time and I hate it.

maybewhenthesun 9 hours ago

Interesting.

Had a lenovo thinkpad (another model though) 'die' one me. No way to turn it on. Actually opened it up and did some simple troubleshooting with a voltmeter, checking required voltages according to some guide. No dice. completely dead. 2 months later when I already had a new laptop I was cleaning the cupboard and was going to throw it away. Decided to stick the charger in one more time and see if something worked: good as new. (Had to put all the scavenged parts back in of course, the hdd and the ram mainly).

It has been working fine since (I guess that was about ~10 years ago? )

consp 7 hours ago

My work laptop has a similar fix for when it keeps memory learning forever. You have to unplug the battery completely and press the power button a few times and the next reboot it works again. Had to do this quite a few times until I learned you can enter the advanced settings in the bios to change the memory timings by adding a variable to the uefi partition. It has official memory modules, still keeps learning forever...

gavin_gee 6 hours ago

go look at the forums for ubiquity unifi pro routers. they have the worst behaviour caused by capacitor residual power. they will not restart properly until they are discharged. so if you have a powercut they will not reboot.

you have to unplug for 30 mins, short the power cable pins and then it might reboot

superxpro12 8 hours ago

my lenovo legion does this... im conivnced there's a bug in their hardware power path that latches itself completely off.

the only way i've ever fixed it is by taking off the back panel and removing the battery to let that mystery circuit completely discharge.

I suspect the power button konami code isnt much more than "discharge the flawed circuit so it can work properly again"

hobo123 5 hours ago

Does this also work with Thinkpads with integrated batteries? I'm assuming probably not, as they would constantly try to switch on.

medvidek 5 hours ago

You can still physically disconnect the battery even if it's inside the case. Just takes a screwdriver and a minute instead of a couple seconds.

rickdeckard 8 hours ago

Sounds like all the support-guy wanted to achieve was a full discharge of all capacitors in the device, so he gave a task that ensured that battery and AC are disconnected long enough... :)

ogig 10 hours ago

I did this last week on a dead P52. It worked once, then it died again a few days later, sadly. The procedure I follow is slightly different tho, 60 seconds button press instead of the 10+30s combo. Ill try again tomorrow just in case.

mugsie 9 hours ago

Back in the old days of working the PC Clinic in a PC World this basic thing was the go to for all laptops. You wouldn't believe the amount of broken laptops I brought back to live with this.

brody_hamer 11 hours ago

This sounds very similar to “do the prongs on your power cable have holes in them?”

Which, of course, doesn’t matter. It just forces you to actually unplug your device and plug it back in.

This mostly sounds like a way to get the user to wait a solid minute before plugging the battery back in for capacitors to dissipate. There’s no way the number or duration of power button presses matters.

EmX_3000 28 minutes ago

Wintel version of zapping the PRAM.

post_break 10 hours ago

I love how this is so typical for windows laptops. You put them in your bag and they decide now would be a good time to turn into a nuclear meltdown. I have had this happen with a few laptops, thinkpad included, yet macs never seem to turn on when asleep in a bag.

jeroenhd 8 hours ago

It's a driver thing. Windows itself can do this kind of quick sleep perfectly fine, but manufacturer drivers (and sometimes ACPI bytecode) will block that process or even wake the laptop. Supposedly this has been improved at some point, but I haven't daily driven Windows in ages so I can't say for sure.

On Mac I have the opposite problem: it's impossible to notice whether it's on or not, leading to my Bluetooth headphones often connecting to the laptop stowed away in my work bag two rooms over, preventing me from connecting it to the device I'm actually using without turning on the laptop.

jasonjayr 7 hours ago

Which, is frustrating because of the certification process Microsoft forces on drivers to get signed to work in windows. They could easily own this by mandating that the driver must not interfere with the OS's power management. The changes Windows has made to "modern power management" don't seem to be well planned out, because this 'turn on while in a tight space' problem is happening a lot, and for quite some time.

At some point way back when, Windows laptops would reliably sleep and hibernate, w/o worrying about them turning a laptop bag into a portable oven.

ddtaylor 11 hours ago

I'm currently using an Omen that "died" because I opened and cleaned it without properly discharging and slightly buzzed a random chip, which happened to be the embedded controller that operates before the BIOS does. This is basically the reason you can use USB and do some other stuff before your laptop is actually on. The problem is that when I touched that chip I scrambled some bits that stay powered via a separate internal battery that cannot be disconnected.

At the time I did not know the secret power trick for this laptop, which is a similar way of holding the power button while inserting the charger. Instead I tried a few things and gave up because the behavior was inconsistent and frustrating. I stuffed it in a drawer and moved on with other things for a few months.

Randomly probably two months later I opened that drawer and went "oh yeah", then proceeded to kind of just get back into the same mindset of the problem and make sure I remember it correctly, since I'm too lazy to keep notes sometimes. To my rekindled frustration I pressed the power button and it came on normally - minus a BIOS battery CMOS time thing. Sure, I was happy it worked, but I now randomly think about the fucking hours of dedicated and methodical attempts at isolating hardware components that had potentially failed in vain because this piece of shit was now running some scrambled undefined behavior code on a shadow chip.

taegee 4 hours ago

It's not a thinkpad thing. This is at least a general laptop advice.

You disconnect the power source and drain the remaining electricity in the circuit. That's the only way to bring it back to a definite state. The flip-flops might be in a weird state it's incapable of booting from.

It might also happen that for example your USB fuse triggers but the USB port refuses to come back to life, although it's not damaged. Same procedure here.

The strange code is just to get the person to stay focused on pressing the button long enough.

It's the same as the myth that stinging nettles won't sting if you hold your breath while touching them: When people try this out, they end up focusing intently and only touch the nettle with their fingertips/with parts of their skin that have enough calluses.

Some also call this "cargo cult" (look it up).

piltdownman 11 hours ago

Same as it ever was. Who here is old enough to remember the four key boot combo for clearing the PRAM contents stored on the logic board in New World PPC Macintoshes?

lproven 10 hours ago

Cmd + Opt + P + R

dodger-dog 5 hours ago

Do people still call support, like on the phone?

geekamongus 6 hours ago

Let me guess: up, up, down, down, left, right, left, right, B, A, Start?

attila-lendvai 10 hours ago

same for my X1 Carbon Gen6, except that you need to unscrew the backplate, and disconnect the battery wiring inside. and of course no need to keep pressing the power button, just hold it down long enough to discharge the capacitors.

happens about once a year; i.e. rare enough to scare me each time...

i used to have an LG screen that had to be unplugged once every year or two. it acted completely dead until unplugged.

throw839389 9 hours ago

I have fairly premium machine, where bios froze in idle and would not respond to power button. Disconnecting battery and leaving it over night, did the trick. I would be screwed with macbook or surface laptops!

Gasp0de 6 hours ago

Only if they would freeze like that. Have honestly never heard of this happening to a MacBook.

functionmouse 11 hours ago

Many a computer has been saved by unplugging it and holding the power button, and then clicking it over and over again, and flicking the switch back and forth etc before plugging it back in. :)

eahm 8 hours ago

Yeah, nothing new or secret, the "power" of the capacitors eh.

aa-jv 11 hours ago

My washing machine has a 'secret reset' code .. unplug it for 30 seconds, plug it back in, open and close the door 10 times, wait .. reboots.

I kind of wonder, every time, whether this is a uboot thing.

What a world we live in that our washing machines have a magic-sysreq thing going on ..

nticompass 10 hours ago

My washing machine has a "debug mode" you can get to by turning the dial left/right a specific number of clicks. In this debug mode, you turn the dial to access different "options" which are shown by specific patterns on the lights. I did it once when my machine was having issues, then I realized that I didn't know what I was doing and used my warranty to have someone come and fix it (they had to replace the "control board").

xattt 10 hours ago

I’m sure you could skip the door opening thing by depressing the door sensor “peg”.

dezgeg 8 hours ago

That's what we get when microcontrollers (which have software) are put in everything.

My dishwasher has some button combination which entered right after power up enters factory test / diagnostic mode. It could tell the water temperature, which was useful in diagnosing whether my fix to the heater worked.

Brian_K_White 3 hours ago

Fxtec phone has a super genius power management circuit that requires battery power to activate the charging circuit to accept power from usb.

If the battery ever once goes low enough, it can never be charged again. Even with a charger plugged in, it just ignores it. Long press reset does wake it up but it just immediately shuts itself off again and the battery does not get charged from the usb power.

This actually happened to some people while their new unit was sitting in warehouses before shipping.

The fix (unofficial and unintentional, users discovered it) is to plug in a charger, get a short thick rubber band such as from broccoli, wrap it around the waist to hold the power button down continuously, and just leave it that way long-press boot-looping overnight.

The the long-press detector does trigger and the circuit does wake up and get power from the usb port for about 1 second, then shuts off again and waits for the long-press time again (15 seconds or so).

Every time it wakes up for 1 second, the battery gets a teeny tiny bit of charge. After 4-8 hours it accumulates enough for the power management circuit to work normally and turn itself on and charge normally the rest of the way.

You know it's gone far enough and you can remove the rubber band when you see the power-on boot logo (or anything at all) on the screen during a loop. Until then the screen never shows anything, just the notification led comes on for about a second once per loop.

gambiting 10 hours ago

>>Then I noticed that even though the machine had been asleep, it was really really hot.

Oh you mean the classic windows laptop behaviour of waking up in your bag and cooking itself. Yeah, I've had that on several Dells and even a Razer windows laptop. Now I don't actually dare to put one to sleep, I just have them set to hibernate when the lid is closed - takes a few seconds longer but at least the laptop doesn't randomly turn itself into an air fryer when I'm travelling.

Betelbuddy 8 hours ago

They could have used this post last Friday at the FAA...

pryanshu89 11 hours ago

At this point, the power button is less of a switch and more of a prayer button.

bertonvv 10 hours ago

This technique is known as a CMOS reset

mb_thd 10 hours ago

It's not. For a CMOS reset you either have to pull out the CMOS battery or press the reset button on the mainboard. (If you have either, that is)